CoursesMEC521 Vibrations

Chapter

Chapter 2: SDOF Forced Vibration

Weeks 4–5. Covers AIMS syllabus topic 3.0

What is covered

Week 4 19 Oct to 25 Oct 2026

  • Determination of damping characteristics from measured decay
  • Introduction to harmonic excitation

Week 5 26 Oct to 1 Nov 2026

  • Undamped and damped harmonic excitation
  • Steady-state solution
  • Magnification factor and phase
  • Rotating imbalance
  • Base motion and support excitation
  • Frequency response function
  • Resonance, transmissibility and vibration isolation

Lecture videos

Week 5, 7 parts, about 29 minutes

0 of 7 watched

Progress stays in this browser. Sign in with your UiTM account to record it for your lecturer.

Part 1: A harmonic force, resonance and beating

Not startedOpen the video on its own

Part 2: Damping, magnification and phase

Not startedOpen the video on its own

Part 3: Rotating imbalance

Not startedOpen the video on its own

Part 4: Base motion, and three ratios that look alike

Not startedOpen the video on its own

Part 5: Transmissibility and isolation

Not startedOpen the video on its own

Part 6: Designing an isolating mount

Not startedOpen the video on its own

Part 7: Beliefs, traps and takeaways

Not startedOpen the video on its own

Try it

Cheat sheet

One picture holds the chapter. The three ratios share one denominator; the numerator tells you which machine you have. Only the moving-floor curve crosses 1 exactly at r=√2.One page for Chapter 2The key picture, which formula to use when, and the ways to lose marksOpen the Chapter 2 cheat sheet

Animations

Show the 5 animations from the lecture slides
Watch resonance build up --- and beat: from rest, f_n = 1 Hz: undamped at f_n grows (9.42 X_st after 3 cycles), ζ = 0.05 levels at 10 X_st, 0.9 f_n beats every 10 s
Watch resonance build up --- and beat. From rest, fn = 1 Hz: undamped at fn grows (9.42 Xst after 3 cycles), ζ = 0.05 levels at 10 Xst, 0.9 fn beats every 10 s.
Watch the phase lag grow: steady state at r = 0.2 → 2.4, ζ = 0.10: the mass drawn when the force peaks, MF and phase traced
Watch the phase lag grow. Steady state at r = 0.2 → 2.4, ζ = 0.10: the mass drawn when the force peaks, MF and phase traced.
The unbalanced drum, spinning up: the deck's worked-example washing machine run 0 → 1000 rev/min: peak 2.78 mm at 331 rev/min, 0.77 mm at 900
The unbalanced drum, spinning up. The deck's worked-example washing machine run 0 → 1000 rev/min: peak 2.78 mm at 331 rev/min, 0.77 mm at 900.
Watch the car cross r = √2: quarter car on a 5 m corrugated road, 5 → 70 km/h: worst 28.6 km/h, isolating beyond 40.5 km/h
Watch the car cross r = √2. Quarter car on a 5 m corrugated road, 5 → 70 km/h: worst 28.6 km/h, isolating beyond 40.5 km/h.
Watch the three ratios part company: one sweep r = 0.1 → 4 at ζ = 0.15 (handbook Figure 2.2): a fixed force, a spinning mass and a moving floor side by side; all three peak near r = 1, the floor ratio drops below 1 past r = √2, and at r = 4 the force gives 0.07, the floor 0.10, the spinning mass still 1.06
Watch the three ratios part company. One sweep r = 0.1 → 4 at ζ = 0.15 (handbook Figure 2.2): a fixed force, a spinning mass and a moving floor side by side; all three peak near r = 1, the floor ratio drops below 1 past r = √2, and at r = 4 the force gives 0.07, the floor 0.10, the spinning mass still 1.06.

Download